f ast recover y glass p assiv a ted rectifier vol t age range 50 to 800 v olts current 8.0 amperes features * fast switching * low leakage * low forward voltage drop * high current capability * high surge capability * high reliability mechanical da t a * case: to-220a molded plastic * epoxy: device has u l flammability classification 94v-o * lead: mil-std-202e method 208c guaranteed * mounting position: any * weight: 1.8 grams * polarity: as marking maximum ratings and electrical characteristics ratings at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20%. electrical characteristics (at t a = 25 o c unless otherwise noted) FR801 thru fr806 maximum ra tings (at t a = 25 o c unless otherwise noted) notes : 2. measured at 1 mhz and applied reverse voltage of 4.0 volts 1. test conditions: i f = 0.5a, i r = -1.0a, i rr = -0.25a 3. thermal resistance junction to case. dimensions in inches and (millimeters) ratings maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t c = 75 o c peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (jedec method) typical junction capacitance (note 2) symbol v rrm v dc i o i fsm c j t j , t stg v rms units volts volts volts amps 8.0 200 50 -65 to + 150 amps pf 0 c FR801 fr802 fr803 fr804 fr805 fr806 35 70 140 280 420 560 50 100 200 400 600 800 operating and storage temperature range typical thermal resistance (note 3) r q jc 50 100 200 400 600 800 3 0 c/w at rated dc blocking voltage t a = 25 o c characteristics maximum full load reverse current average, full cycle at t c = 100 o c maximum reverse recovery time (note 1) v f symbol i r trr units 1.3 10 150 uamps uamps nsec maximum dc reverse current maximum instantaneous forward voltage at 8.0a dc volts 150 250 500 FR801 fr802 fr803 fr804 fr805 fr806 rohs product for packing code suffix "g" halogen free product for packing code suffix "h" * .270(6.90) .230(5.80) .157 (4.00) .039(1.00) .023(0.60) .051 (1.30) .187(4.82) .148(3.80) .053(1.3) .043(1.1) .028(0.70) .014(0.36) .126 (3. 20) .129(3.3) .1(2.54) .153(3.9) .146(3.7) .583(14.8) .531(13.5) .413(10.5) .374(9.5) .624(15.87) .578(14.70) .102(2.60) .091(2.30) .04 max . (1.0) to-220a
rating and characteristic curves ( FR801 thru fr806 ) fig. 1 - typical forward current average forward current, (a) case temperature, ( o c) derating curve single phase half wave 60hz inductive or resistive load 8 6 4 2 0 0 25 50 75 100 125 150 175 junction capacitance, (pf) fig. 5 - typical junction capacitance reverse voltage, ( v ) 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 t j = 25 o c fig. 3 - typical instantaneous forward characteristics instantaneous forward current, (a) instantaneous forward voltage, (v) t j = 25 o c pulse width=300us 1% duty cycle 20 10 3.0 1.0 0.3 0.1 .03 .01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 trr +0.5a 0 -0.25a -1.0a 1cm set time base for 50/100 ns/cm fig. 6 - test circuit diagram and reverse 50 noninductive 10 noninductive d.u.t 25 vdc (approx) ( - ) ( - ) ( + ) ( + ) 1 non- inductive oscilloscope (note 1) pulse generator (note 2) notes: 1 rise time = 7ns max. input impedance = 1 megohm. 22pf. 2. rise time = 10ns max. source impedance = 50 ohms. recovery time characteristic t j = 25 fig. 4 - typical reverse characteristics instantaneous reverse percent of rated peak reverse voltage, (%) current, (ua) 10 .01 .02 .04 .06 .1 .2 .4 .6 1.0 2 4 6 0 20 40 60 80 100 120 140 fig. 2 - maximum non-repetitive forward peak forward surge number of cycles at 60hz 300 250 200 150 100 50 0 1 2 5 10 20 50 100 surge current current, (a) 8.3ms single half sine-wave (jeded method)
|
